Safety Peel 1 Environmentally Responsible Paint Remover

Safety Peel 1 – Environmentally Responsible Paint Remover Without Methylene Chloride or Methanol

Safety Peel 1 is a solvent paste paint remover formulated for the removal of paint, graffiti, and clear coatings from masonry and other surfaces. Manufactured by PROSOCO under the Enviro Klean product line, it is designed for contractors and trades professionals who require effective paint stripping without the hazards associated with conventional chemical paint removers containing methylene chloride or methanol. Its mild citrus odor and interior suitability make it viable for enclosed or occupied jobsite environments where ventilation is limited.

Unlike conventional strippers, Safety Peel 1 uses a slow-working paste mechanism that traps hazardous paint solids as it dries, allowing the entire mass — including potentially hazardous paint waste — to be peeled away intact. This substantially reduces waste volume and simplifies containment and disposal, making it particularly well-suited for lead-based paint abatement projects where waste management is a primary concern.

Technical Specifications

Key Features & Benefits

No Methylene Chloride or Methanol

Safety Peel 1 contains neither methylene chloride nor methanol, two of the most hazardous chemicals found in conventional paint removers. This significantly reduces applicator health risks and regulatory exposure on jobsites where stricter chemical handling requirements apply.

Paste Containment of Hazardous Paint Solids

As the paste dries, it traps hazardous paint solids — including lead particles — within the semi-dry mass. The entire poultice is then peeled from the surface as a single unit, simplifying containment and substantially reducing waste volume compared to liquid strippers that spread contaminants during removal.

Slow Drying for Extended Dwell Time

Safety Peel 1 remains active for up to 12 hours when left uncovered and up to 24 hours when covered with PROSOCO's OverCoat protective paper. This extended dwell time allows a single application to dissolve multiple layers of paint, reducing the number of treatment cycles required on heavily coated surfaces.

No Surface Neutralization Required

After removal, Safety Peel 1 rinses easily with cold or hot water and requires no surface neutralization step. This eliminates a time-consuming process step and reduces the number of products needed on the jobsite.

Suitable for Lead-Based Paint Abatement

Safety Peel 1 was specifically developed for lead-based paint abatement projects where removal, containment, and disposal of lead-containing waste are primary concerns. The paste consistency adheres to vertical surfaces and prevents airborne lead particles, supporting compliance with abatement project requirements.

Trowel or Spray Application

The product can be applied by trowel or compatible spray equipment, giving contractors flexibility in application method based on project scale and surface geometry. Spray equipment must be fitted with solvent-resistant seals, poly-lined chemical-resistant hose, and a minimum 1/4-inch orifice tip to prevent fouling.

Common Applications

Lead-Based Paint Abatement

Safety Peel 1 was purpose-developed for lead-based paint abatement, where the paste's ability to trap and contain lead solids during removal simplifies compliance with waste containment and disposal requirements.

Graffiti Removal

The solvent paste formulation is effective for removing graffiti coatings from masonry and other surfaces, with the paste consistency allowing it to adhere to vertical surfaces during dwell time.

Clear Coating Removal

In addition to paint removal, Safety Peel 1 is formulated for removal of clear coatings, expanding its utility on restoration and surface preparation projects.

Multi-Layer Paint Removal

The slow-working formula typically requires only one application to dissolve multiple layers of paint, making it efficient on surfaces with heavy coating buildup.

Interior Paint Stripping

The mild citrus odor and suitability for interior use make Safety Peel 1 appropriate for enclosed environments such as building interiors where conventional high-odor strippers would be impractical or prohibited.

Compatible Materials

• Masonry surfaces
• Vertical surfaces (paste consistency provides adhesion)
• Surfaces with multiple paint layers
• Surfaces requiring lead-based paint abatement

Product Documents

• Product Data Sheet
• Safety Data Sheet
• Safety Data Sheet (Spanish)
• SDS Canadian French

Application Instructions

Preparation

1. Protect people, vehicles, property, and all non-masonry surfaces from product, splash, residue, fumes, rinse water, and wind drift.
2. Protect and/or divert pedestrian and auto traffic from the work area.
3. Ensure surface and air temperatures are at least 40°F (4°C) during application. Product efficiency is reduced in cold weather.
4. Read the full Safety Data Sheet and product label before use.

Testing

1. Always test a small area of each surface and paint coating to confirm suitability, dwell times, coverage rate, and desired results before beginning overall application.
2. Test with the same equipment and application procedures planned for general application.
3. Allow Safety Peel 1 to dwell at least two hours before removing and evaluating the test area.

Mixing and Dilution

1. Apply as packaged. Do not dilute or alter the product.
2. Stir well before use.

Application

1. Apply Safety Peel 1 using a trowel or suitable spray equipment at a thickness of 1/16 to 1/8 inches.
2. If using spray equipment, fit with solvent-resistant seals and parts, a poly-lined chemical-resistant pressure-rated hose, and spray tips with a minimum 1/4-inch orifice. Adjust sprayer to the lowest pressure setting to produce a slow, even flow.
3. Before the paste dries, cover with PROSOCO's OverCoat protective paper (glossy side down) and tape down the edges. OverCoat keeps the paste moist, increases paint-removal effectiveness, and protects passersby from incidental contact.
4. Allow to dwell up to 12 hours (uncovered) or up to 24 hours (with OverCoat).

Removal and Rinsing

1. Peel the dried paste from the surface. The paste will carry trapped paint solids with it.
2. Dispose of the peeled paste and trapped paint solids in accordance with local, state, and federal regulations.
3. Rinse the surface with cold or hot water. No surface neutralization is required.

Storage and Handling

1. Store in a cool, dry place away from potential ignition sources. Maintain temperature of 45–100°F (7–38°C).
2. Always seal container after dispensing. Do not double stack pallets.
3. Do not alter or mix with other chemicals.
4. Dispose of in accordance with local, state, and federal regulations.

Safety Data Summary

Hazard Information

• Harmful if inhaled (Acute toxicity – Inhalation, Category 4)
• Causes skin irritation (Category 2)
• Causes serious eye irritation (Category 2)
• Suspected of causing cancer (Carcinogenicity, Category 2)
• May damage fertility or the unborn child (Reproductive toxicity, Category 1B)
• May cause respiratory irritation; may cause drowsiness or dizziness (STOT single exposure, Category 3)
• May be harmful if swallowed
• May be harmful in contact with skin

Personal Protective Equipment

• Wear appropriate eye/face protection
• Use personal protective equipment as required
• Avoid breathing dust, fume, gas, mist, vapors, or spray
• Use only outdoors or in a well-ventilated area
• Wash face, hands, and any exposed skin thoroughly after handling
• Obtain special instructions before use; do not handle until all safety precautions have been read and understood

Safe Handling

• Store locked up in a well-ventilated place with container tightly closed
• If exposed or concerned, get medical advice/attention
• If in eyes: rinse cautiously with water for several minutes; remove contact lenses if present and easy to do; continue rinsing; seek medical attention if irritation persists
• If on skin: wash with plenty of soap and water; seek medical attention if irritation persists; remove and wash contaminated clothing before reuse
• If inhaled: remove to fresh air and keep at rest in a position comfortable for breathing
• Dispose of contents and container at an approved waste disposal facility
• 24-Hour Emergency Information: INFOTRAC at 800-535-5053
• Business hours: 785-865-4200 (8:00 AM – 5:00 PM CST, Monday–Friday)

Frequently Asked Questions

Q: Does Safety Peel 1 require surface neutralization after use?
A: No. After peeling the paste, the surface rinses easily with cold or hot water and no neutralization step is required.

Q: How long should Safety Peel 1 be left on the surface?
A: When left uncovered, Safety Peel 1 remains active for up to 12 hours. When covered with PROSOCO's OverCoat protective paper, dwell time extends to up to 24 hours. Always test a small area first — a minimum evaluation dwell of two hours is recommended before assessing results.

Q: Can Safety Peel 1 be used for lead-based paint abatement?
A: Yes. Safety Peel 1 was specifically developed for lead-based paint abatement projects. The paste traps lead-containing paint solids as it dries, and the entire mass is peeled away intact, simplifying containment and disposal of lead-containing waste.

Q: How many layers of paint can a single application remove?
A: Usually just one application dissolves multiple layers, though results depend on the specific paint types and surface. Always test before full application.

Q: What is included with a 5-gallon pail of Safety Peel 1?
A: Each 5-gallon pail includes a 10-pack of PROSOCO's OverCoat protective paper film, which is used to cover the applied paste to maintain moisture and increase paint-removal effectiveness.

Q: Is Safety Peel 1 compliant with VOC regulations?
A: Yes. Safety Peel 1 is compliant with all national, state, and district VOC regulations, with a VOC content of 30% maximum.