Skip to content

Chem-Rock Accelerator (1 Pint Jar)

SKU 519X
 
Original price $26.00 - Original price $26.00
Original price
$26.00
$26.00 - $26.00
Current price $26.00
  • Amazon
  • American Express
  • Apple Pay
  • Diners Club
  • Discover
  • Google Pay
  • Mastercard
  • PayPal
  • Shop Pay
  • Venmo
  • Visa

Chem-Rock Accelerator

Available Sizes
  • 1 pint jar
Advantages
  • Quicker project completion times without sacrificing product quality
  • Does not affect physical performance of cured accelerated product
  • Does not affect clarity of accelerated product
  • VOC compliant
  • Cost Effective
  • Easy application

Description

CHEM-ROCK ACCELERATOR is a clear liquid additive to be used in with CHEM ROCK HV, MV or LV CLEAR when a faster than normal cure time is required on fast track installations.

Mixing Instructions

CHEM-ROCK ACCELERATOR is to be added after CHEMROCK Parts A and B have been mixed for 2 minutes according to their instructions. The entire 9 oz. container of CHEM-ROCK ACCELERATOR should be poured into the pre-mixed 3 gallons of CHEM-ROCK and mixed on low speed for an additional 2 minutes. Immediately after mixing the accelerated CHEMROCK must be poured out of the bucket and onto to the working surface and quickly installed using normal application procedures.

Comparison of Chem-Rock Products

- Average cure time of standard products vs. with addition of Chem-Rock Accelerator
Stardard Formulations of Chem-Rock With Chem-Rock Accelerator
Standard Formula Chem-Rock LV
  • Gel Time: 32 minutes
  • Time to Recoat: 2.5 hours
  • Time to cure (open for foot traffic): 8 hours
Chem-Rock LV with Accelerator
  • Gel Time: 22 minutes
  • Time to Recoat: 2 hours
  • Time to cure (open for foot traffic): 7.5 hours
Standard Formula Chem-Rock MV
  • Gel Time: 45 minutes
  • Time to Recoat: 3.5 hours
  • Time to cure (open for foot traffic): 9 hours
Chem-Rock MV with Accelerator
  • Gel Time: 26 minutes
  • Time to Recoat: 2 hours
  • Time to cure (open for foot traffic): 5.5 hours
Standard Formula Chem-Rock HV
  • Gel Time: 55 minutes
  • Time to Recoat: 4 hours
  • Time to cure (open for foot traffic): 9 hours
Chem-Rock HV with Accelerator
  • Gel Time: 22 minutes
  • Time to Recoat: 2 hours
  • Time to cure (open for foot traffic): 5.5

Limitations & For Best Results

  • Do not thin this product.
  • Do not exceed the recommended ratio of 9 oz. ACCELERATOR per 3 gallons mixed CHEMROCK
  • Use CHEM-ROCK ACCLERATOR only in clear CHEM-ROCK coatings
  • Do not use CHEM-ROCK ACCELERATOR with any other products besides CHEM-ROCK HV, MV or LV
  • Follow application and mixing instructions above and as provided for individual CHEMROCK HV, MV and LV products

Product Application

Apply CHEM-ROCK products by brush, roller or squeegee. ROCK-TRED product test data is based on environmental temperatures of 75° F (24° C). Viscosity and working time are always affected by temperatures above or below that mark. When applying product – always consider the ambient, surface, and product temperature at the time and place of installation.

Chemical Resistance

Always refer to ROCK-TRED's chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.

Product Storage

DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.

Surface Preparation

Always apply ROCKTRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Surface preparation by means of a shot-blasting machine is the best and recommended method for attaining the desired profile. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.

Clean Up

Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.

Disposal

Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.

Important Notice

Always read and acquaint yourself with ROCK-TRED's Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty.