Available Sizes
  • 2.5 Gallon Kit packaged in two pails
  • 12.5 Gallon Unit packaged in three 5 gallon pails
  • 138 Gallon Bulk Unit packaged in three drums
  • 100% solids
  • Field pigment in any ROCKTRED solid color
  • Broad spectrum chemical resistance
  • Highly durable and abrasion resistant
  • VOC compliant
  • Resists elevated temperatures


NOVO-POXI is a high-performance, 100% solids, NOVOLAC epoxy that can be used as a body/basecoat or as a topcoat. Reformulated in 2013 for easier application and product flow NOVO POXI has not sacrificed any performance for better functionality. NOVO-POXI is VOC compliant and meets all of the USDA/FDA guidelines for use in federally inspected facilities.


NOVO-POXI is installed as a solid color high density specialty coating with broad spectrum chemical resistance and resistance to elevated temperatures. NOVO-POXI will resist splash/spill exposure and immersion exposure to many industrial chemicals with little effect. NOVO-POXI can be used in areas where temperatures are consistently above 180° F and/or where intermittent temperatures reach 200° F.

Typical Coverage

NOVO-POXI is typically applied between 50 - 125 square feet per gallon per coat depending upon substrate and project requirements. NOVO-POXI is a higher viscosity material designed for application in heavy coats.

Physical Properties

Volume mix ratio 1.5 to 1 (Resin to Hardener)
Viscosity (mixed) 2200-3000 CPS Typical
Solids Content (%) 100 % (ASTM D-2697)
Hardness (ASTM D-2240) 75 - 80 (Shore D)
VOC Compliant with all US Regulations
Application Temps. 60° – 85° F
Gel Time 20-35 minutes @ 75° F
Dry to Touch (recoat with compatible products) 1.5 – 3.5 hours @ 75° F
Through Cure 3.5 – 5.5 hours @ 75° F
Open for light traffic 24 hours @ 75° F
Shelf life 1 year in unopened units
Ready for Chemical / Heat Exposure Minimum of 48 hours @ 75° F (Can be up to 7 days to fully cross link)

Limitations & For Best Results

  • Do not thin this product.
  • Do not apply when Humidity exceeds 70% indoors.
  • Do not allow to puddle during application.
  • When re-coating, always apply the next coat within 24 hours of completing the previous coat.
  • Allow each coat to dry to 'tack-free' or clear prior to re-coat.
  • When pigmenting this product using light colors application at 15 mils or in multiple coats may be required for full hide.

Product Application

Apply using brush, roller and squeegee ROCK-TRED product test data is based on environmental temperatures of 75° F. Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.

Color and Textures

NOVO-POXI is manufactured in CLEAR (amber color) and can be field pigmented using ROCK-TRED colorants. Most ROCK-TRED products are available in a wide range of textures using an appropriate aggregate.

Chemical Resistance

Always refer to ROCK-TRED's chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.

Product Storage

DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.

Surface Preparation

Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a shotblasting or diamond grinding machine to a minimum CSP-2 profile followed by application of an appropriate ROCK-TRED primer or base system is the best and recommended installation method for NOVO-POXI applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.

Clean Up

Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.


Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.

Important Notice

Always read and acquaint yourself with ROCK-TRED's Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty.