Dry Treat Meta Creme - Stain-Proof Waterborne Dense Surface Sealer

Pack size

1 Quart (946 mL) recyclable soft pack
2.5 Gallons (9.46 L) bucket

Sizes not available in all countries.

Active content

Approximately 50 percent active content in a hybrid micron particle sized water/non-water colloidal mixture. VOC content meets US EPA < 100 grams per Liter (Method 24, excluding water and exempt compounds). Fulfills LEED requirements (Waterborne Dense Stone Sealer will qualified for EQ Credit 4.2: Low-Emitting Materials: Paints & Coatings 1 Point). Compliant with EU VOC Directives 2004/42/CE and 1999/13/EC and Environmental Protection Department Hong Kong SAR Government 2007 Regulations.

How To Use

1. ALWAYS TEST PRODUCT ON A SMALL AREA FIRST and allow a 24-hour cure time to determine the ease of application and desired results.
2. Surfaces to be treated must be dry, clean and free of residues, and surface temperature between 40 - 95°F ( 5 - 35°C).
3. Generously coat the surface with Waterborne Dense Stone Sealer using a foam roller, brush, or similar. Avoid contact with surrounding areas.
4. Leave the product to penetrate for minimum 1 hour, then thoroughly polish with a clean dry cloth (or squeegee) to remove ALL excess product. Estimated application rate is 1 quart per 30 to 100 square feet (1 litre per 3 to 10 sq.m.), depending on surface absorption.
5. Use fresh water to clean equipment.
6. Avoid moisture contact with the surface for a minimum of 12 hours after application.
7. Sealer will NOT prevent surface etching, scuffing or wear and may lighten or darken some surfaces. To clean treated surfaces, use a neutral pH detergent in warm water and a soft cloth or mop.

Waterborne Dense Stone Sealer Professional Application Hints

1. TESTING WATERBORNE DENSE STONE SEALER
Waterborne Dense Stone Sealer must be allowed to cure for at least 4 weeks before undertaking testing.

• Achieving optimum stain repellence
  Waterborne Dense Stone Sealer’s specially designed sealing molecules migrate through the pores and find sites to bond by a process of chemical reaction, over 4 to 5 weeks! As more Waterborne Dense Stone Sealer bonds inside the pores, the material becomes more oil and water-repellent. After 24 hours of cure time, the product will show only adequate stain repellency and zero penetration, but after 3 weeks cure time the results will be significantly better.
• Achieving maximum depth of penetration
  The modified silane molecules in Waterborne Dense Stone Sealer are hundreds of times smaller than the best modern competitor (fluorocarbon /siloxane) sealers, which cannot penetrate into the pores of dense materials, such as polished granites. With 4 hours of dwell time and 4+ weeks of cure time, typical penetration of Waterborne Dense Stone Sealer into Kashmir white granite is 7 to 13 millimeters.

 2. APPLYING WATERBORNE DENSE STONE SEALER ON DENSE / POLISHED SURFACES

• For extra penetration Waterborne Dense Stone Sealer may be left to penetrate for up to 4 hours on smaller polished surfaces such as countertops.

 3. APPLYING Waterborne Dense Stone Sealer ON SMOOTH SURFACES

• Once Waterborne Dense Stone Sealer has been left for at least one hour to penetrate a smooth (honed / polished / antiqued) surface, a squeegee can be used to speedily remove the bulk of the product residue. Then, the small amount of remaining excess product / residue can be easily polished off with dry absorbent cloths. If the Waterborne Dense Stone Sealer residue has begun to dry and cannot be polished off with a dry cloth, the cloth can be moistened with a small amount of Waterborne Dense Stone Sealer to aid removal. 

 4. APPLYING Waterborne Dense Stone Sealer ON HIGHLY POROUS MATERIALS

• Highly porous / absorbent surfaces, such as sandstone and soft varieties of limestone should be pre-sealed before applying Waterborne Dense Stone Sealer. Newly laid floors should also be pre-sealed prior to grouting, so that the grout is easy to remove and does not cause stains. Once the grout is dry and all grout haze has been thoroughly removed, Waterborne Dense Stone Sealer can be applied over the tiles and grout. A light sprayed coat of STAIN-PROOF^® Waterbased Penetrating Sealer, formerly known as STAIN REPELLA™, makes a cost effective pre-sealer, and requires only 2-3 hours of drying time before applying grout or a coat of Waterborne Dense Stone Sealer.

 5. APPLYING WATERBORNE DENSE STONE SEALER ON ROUGH SURFACES

• On rough surfaces, globules of Waterborne Dense Stone Sealer may collect in gaps and pits. Use a paint brush to remove these globules and spread them out.

Application Rate

Waterborne Dense Stone Sealer Downloads

STAIN-PROOF Brochure

Sealer Application Rates

Waterborne Dense Stone Sealer Specification Sheet

Waterborne Dense Stone Sealer Overview

Product Uses And Porosity Chart

Maintaining Sealed Surfaces

General Surface Maintenance Guide

STAIN-PROOF has produced a comprehensive, easy-to-read guide to maintaining your sealed (or unsealed) porous surface, including stone surfaces. 

STAIN-PROOF Surface Maintenance Guide is divided into clear sections for easy use - indoor and out door surfaces, horizontal and vertical surfaces, heavy duty cleaning, light regular cleaning, stain removal and tackling special problems such as salt efflorescence and grout haze.

Download our Surface Maintenance Guide

Countertop Care Sheet

Specification Clauses

Construction Specifications Institute format

Leed Certificate

LEED Compliance Certificate

Safety Data Sheets

Waterborne Dense Stone Sealer SDS (USA)

Waterborne Dense Stone Sealer SDS (ESP)

Illustrations

Close up of pores

Permanent bonding